The simple way to boost your broadleaf control. |
 |
Application Procedures
Timing
In Crop:
Wheat (including Durum), barley and triticale
• 2-leaf minimum, but before flag leaf is visible.
• Do not harvest within 45 days of the last application.
Can also be used for: Pre-Plant Burndown, Post Harvest and Fallow. See AUDIT label for specific use recommendations.
Crop Rotation
• Wheat, barley and triticale may be replanted anytime after the application of AUDIT.
• Sugarbeets, winter rape and canola can be planted 60 days after the application of AUDIT
• Any other crop may be planted 45 days after the application of AUDIT.
Rate
Do not use less than 0.133 ounce/A of AUDIT WDG Herbicide
Wheat (including Durum), barley and triticale
• Spike Rate1 0.133 ounce/A
• Low Rate 0.4 ounce/A
• High Rate 0.66 ounce/A
1The Spike Rate of AUDIT in a tank-mix with other suitable registered herbicides will provide control of selected broadleaf weeds including: Annual Smartweeds, Common Lambsquarters, Pigweeds (Redroots and others), Velvetleaf and Wild Mustard as well as suppress Cocklebur and Wild Sunflower. For broad-spectrum control of weeds listed in the “TANK MIXTURES” section of the AUDIT label, 0.4 to 0.66 oz/A use rates are required.
Pre-Plant Burndown, Post Harvest and Fallow
• Low Rate 0.4 ounce/A
• High Rate 0.66 ounce/A
Sequential treatments of AUDIT WDG Herbicide may also be made provided the total amount of AUDIT applied to the crop or during one fallow/preplant season does not exceed 1.2 ounces/A.
Tank-mix Partners
GRASS
Axial XL®
Discover®
EVEREST®
Maverick®
Puma®
BROADLEAF
2,4-D (amine or ester)
Banvel®
Bison®
Bronate®
Bronate Advanced®
Buctril®
Clarity®
Curtail®
Curtail M®
MCP (amine or ester)
Rhino®
Salvo®
Starane®
Starane + Salvo®
Starane + Sword®
WideMatch®
See individual product labels for the complete list of weeds controlled as well as tank-mixing and application directions, rate, timing and specific precautions.
Mixing Instructions
Ground Application
Do not use with spray additives that alter the pH of the spray solution below pH 6.0 as rapid product degradation can occur.
Ensure the spray tank is clean. For optimum spray distribution and thorough coverage, use flat-fan or low-volume flood nozzles. “Raindrop RA” nozzles are not recommended for AUDIT applications, as weed control performance may be reduced. Use screens that are 50-mesh or larger.
- Fill the spray tank ¼ to ⅓ full with clean water.
- While agitating, add the required amount of AUDIT.
- Continue agitation until AUDIT is fully dissolved, at least 5 minutes.
- Once AUDIT is fully dissolved, maintain agitation and continue filling tank with water.
- As the tank is filling, add the other tank mix partners and then add the required volume of spray adjuvant. Always add spray adjuvant last. Antifoaming agents may be used.
- Dispersed tank mix partners can settle if the tank mix is not continually agitated. If settling occurs, thoroughly re-agitate before use.
- Apply AUDIT spray mixture within 24 hours of mixing to avoid product degradation.
- If AUDIT and a tank mix partner are to be applied in multiple loads, fully dissolve the AUDIT in clean water prior to adding to the tank.
Note: AUDIT must be completely dissolved in clean water before adding to spray tanks that do not have continuous agitation during loading and mixing. (this is common for airplanes with turbine engines).
